View Full Version : Having a match grade barrel melonited/nitrided
JeepsAndGuns
07-30-2017, 07:28 PM
So it looks like I am about to build a new 308.
I was wondering if anyone here has any opinions on having a new (hand lapped) match barrel nitrided/melontied. Everything I find online is AR15 specific, and very little about bolt action rifles. But at the same time, everything I find says that it will not effect accuracy (will not make it better or worse). And on the plus side, the barrel will last a ridiculously long time. Seems like the general consensus is, if you start with a crap barrel, have it nitrated, it is still a crap barrel, it will just last forever. On the other hand, start with a high quality match barrel, have it nitrited, it will still be match grade, just last forever.
I have a 4140 barrel on my target rifle and after around 2k rounds, I am starting to get some throat erosion and the surface is got the heat cracking (using a bore scope to see it). So the idea of the nitride/melonite done to it to make it last longer is very appealing to me.
RustyShackle
07-31-2017, 12:30 AM
I have been researching this some lately, I'm curious also.
LoneWolf
07-31-2017, 08:15 AM
On a 308 you'd be wasting your money in my opinion. Unless burning up an obscene amount of rounds you're going to see a at least 5,000 rounds barrel life with a 308 and up to 10,000 rounds depending on your accuracy requirements. Also stainless steel match barrels can not be nitrite treated from my research. Now I'm currently running a Cryo treated barrel from XCaliber on my 6.5x47, but I only have about 425rds on the barrel currently. I expect at least 3K, but will keep running it as long as it lasts for a good test as long as it meets my accuracy requirements to stay competitive. You may see some benefit on a hot 6mm or 6.5 something with a much lower round count, but I would just get a standard match grade barrel for a 308.
J.Baker
07-31-2017, 11:27 AM
You can nitrite stainless steel, it's just not really worth it as it doesn't work nearly as well on SS as it does CM. You will get a higher surface hardness and more corrosion resistance just like with a CM barrel, but if CM gives you 100% improvement in those areas you'll only see maybe 20-40% of that with SS. As such the cost v benefit isn't nearly as good with SS as it is for CM so most don't bother.
JeepsAndGuns
08-01-2017, 07:26 PM
The obscene amount of rounds it would take to wear it out is a plus for me, as it would probably quite literally last me the rest of my life. I would probably end up using the 308 barrel as a test mule and see how it shoots/performs.
The above mentioned barrel with the throat erosion is a 6.5x55 I built on a savage action. The barrel is a douglas premium.
JeepsAndGuns
08-12-2017, 07:36 PM
Well I went ahead and did it. I ordered a X-caliber 26 inch bull barrel. I opted for the cryo treatment and am having them nitride it. I suppose I will be the test mule.
I will report back in a couple months when it gets here and I get a chance to shoot it.
Certainly looking forward to it.
Cryro like in cold dipped in Nitrogen?
I figure I am putting at least 3,000 rounds a year through each barrel so that add up to a new one all to quickly.
What is the cost of each?
JeepsAndGuns
08-13-2017, 09:35 AM
http://www.x-caliber.net/savage-pre-fit
Build one yourself and find out.
I opted for 1-10 twist, 5R, 26 inch, 5/8-24 threaded muzzle, and savage bull contour.
snowgetter1
08-17-2017, 10:22 PM
I had a Shilen 28" 243 wssm nitrided. I was advised by the nitrider, don't remember the place now, to fire approximately fifty rounds the clean it completely. After nitriding I had velocity increases of 100-150fps with all loads except 105gr stayed the same. On a regular nitrided 243 Winchester, Criterion barrel I think, I had velocity decreases of about 50-100fps. That was explained as being from less friction in the barrel. Accuracy did not seem to change after nitriding. Both always shot great.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.